October 2007701P47034DocuTech 128/155/180 HighLight ColorGuideOperator
viii DocuTech 128/155/180 HighLight Color Operator GuideIntroduction• “Technical information” contains the hardware and software capacity guidelines f
3-54 DocuTech 128/155/180 HighLight Color Operator GuideRoutine maintenance1. Open the finisher doors.2. Lift the stitcher panel, which is located dir
DocuTech 128/155/180 HighLight Color Operator Guide 3-55Routine maintenanceFigure 3-53 Removing the stitcher wire plug5. Perform one of the following
3-56 DocuTech 128/155/180 HighLight Color Operator GuideRoutine maintenance• If there is wire on the spool, hold it on the spool and carefully rewind
DocuTech 128/155/180 HighLight Color Operator Guide 3-57Routine maintenancea. Locate the green pin release handle under spool B, as shown in figure 3-
3-58 DocuTech 128/155/180 HighLight Color Operator GuideRoutine maintenanceFigure 3-58 Replacing the pin9. Remove any damaged wire.WARNING: Hold the
DocuTech 128/155/180 HighLight Color Operator Guide 3-59Routine maintenanceFigure 3-59 Removing the paper wrapperNOTE: Hold the wire between the thum
3-60 DocuTech 128/155/180 HighLight Color Operator GuideRoutine maintenance12. Slowly and carefully pull about 3 feet (1 meter) of wire from the spool
DocuTech 128/155/180 HighLight Color Operator Guide 3-61Routine maintenanceFigure 3-61 Storing binder tape in a cool, dry placePerform the following
3-62 DocuTech 128/155/180 HighLight Color Operator GuideRoutine maintenanceReplacing the binder tape reelNOTE: Production publisher configuration on
DocuTech 128/155/180 HighLight Color Operator Guide 3-63Routine maintenanceFigure 3-64 Removing the tapeb. Rewind the tape onto the tape reel.4. Slid
DocuTech 128/155/180 HighLight Color Operator Guide 1-11 Safety noticesSystem safetyIt is your responsibility to ensure your Xerox equipment is safe a
3-64 DocuTech 128/155/180 HighLight Color Operator GuideRoutine maintenanceNOTE:NOTE: The tape will not feed properly if the retainer is not locked.b.
DocuTech 128/155/180 HighLight Color Operator Guide 3-65Routine maintenanceFigure 3-68 Threading the tape to the pressure roll8. Turn the green knob
3-66 DocuTech 128/155/180 HighLight Color Operator GuideRoutine maintenanceFigure 3-70 Cutting the tape10. Close the binder drawer.11. Close the fini
DocuTech 128/155/180 HighLight Color Operator Guide 3-67Routine maintenanceFigure 3-71 Locating the binder tape knobThe knob is spring loaded and mov
3-68 DocuTech 128/155/180 HighLight Color Operator GuideRoutine maintenanceFigure 3-72 Adjusting the tape position up• Pull the knob and rotate it co
DocuTech 128/155/180 HighLight Color Operator Guide 3-69Routine maintenanceReplacing the Customer Replaceable FilterWhen directed by the screen messag
3-70 DocuTech 128/155/180 HighLight Color Operator GuideRoutine maintenance6. Remove the filter housing cover and set it on the piece of paper from st
DocuTech 128/155/180 HighLight Color Operator Guide 4-14 Problem SolvingThe system is designed to help you find and solve problems as they happen. The
4-2 DocuTech 128/155/180 HighLight Color Operator GuideProblem SolvingWhen a fault occursWhen a fault occurs in the printer an indicator appears on th
DocuTech 128/155/180 HighLight Color Operator Guide 4-3Problem SolvingPaper path jams • Check the area where the jams are occurring to ensure that the
1-2 DocuTech 128/155/180 HighLight Color Operator GuideSafety noticesOzone safetyThis product produces ozone during normal operation. The ozone produc
4-4 DocuTech 128/155/180 HighLight Color Operator GuideProblem SolvingMissing sheets in a set immediately after a jam.After recovering from a jam, an
DocuTech 128/155/180 HighLight Color Operator Guide 4-5Problem SolvingProcessor power is off unexpectedlyThe processor or the FreeFlow Print Server ma
4-6 DocuTech 128/155/180 HighLight Color Operator GuideProblem SolvingSolving print quality problemsA print quality problem means that the job was sub
DocuTech 128/155/180 HighLight Color Operator Guide 4-7Problem SolvingClearing paper jams in printer areas 2 through 10 for both configurationsIn the
4-8 DocuTech 128/155/180 HighLight Color Operator GuideProblem SolvingFigure 4-3 Area 4Figure 4-4 Area 5
DocuTech 128/155/180 HighLight Color Operator Guide 4-9Problem SolvingFigure 4-5 Area 6Figure 4-6 Area 7
4-10 DocuTech 128/155/180 HighLight Color Operator GuideProblem SolvingFigure 4-7 Area 8NOTE: If a jammed sheet rips as you are removing it from area
DocuTech 128/155/180 HighLight Color Operator Guide 4-11Problem SolvingFigure 4-8 Area 9To clear jams from area 9:1. Lower and pull out tray 1 to give
4-12 DocuTech 128/155/180 HighLight Color Operator GuideProblem SolvingFigure 4-9 Area 10Figure 4-10 Area 11 (all feeder/stackers)NOTE: High volume p
DocuTech 128/155/180 HighLight Color Operator Guide 4-13Problem SolvingFigure 4-11 Area 12 (all feeder/stackers)NOTE: High volume printer configurati
DocuTech 128/155/180 HighLight Color Operator Guide 1-3Safety notices– The power cable is damaged or frayed.– Liquid is spilled into the system.– The
4-14 DocuTech 128/155/180 HighLight Color Operator GuideProblem SolvingClearing paper jams in the Feeder/StackersFigure 4-12 Area 13NOTE: Figures 4-1
DocuTech 128/155/180 HighLight Color Operator Guide 4-15Problem SolvingNOTE: You may sometimes find paper lying on top of area 14, even though there
4-16 DocuTech 128/155/180 HighLight Color Operator GuideProblem SolvingFigure 4-15 Area 16NOTE: High volume printer configuration only
DocuTech 128/155/180 HighLight Color Operator Guide 4-17Problem SolvingFigure 4-16 Area 17NOTE: If your printer has frequent jams in this area, you m
4-18 DocuTech 128/155/180 HighLight Color Operator GuideProblem SolvingFigure 4-17 Area 18Points to note for clearing jams in area 18:• Sometimes the
DocuTech 128/155/180 HighLight Color Operator Guide 4-19Problem SolvingFigure 4-18 Area 193. Remove any paper from the exposed area.4. Press the green
4-20 DocuTech 128/155/180 HighLight Color Operator GuideProblem SolvingFigure 4-19 Area 206. Remove any paper from the exposed area.7. Press the green
DocuTech 128/155/180 HighLight Color Operator Guide 4-21Problem Solving3. For the processor feeder trays, press the green lever to unlatch the paper f
4-22 DocuTech 128/155/180 HighLight Color Operator GuideProblem SolvingFigure 4-22 6. Slide the tray back into the printer until the tray latches and
DocuTech 128/155/180 HighLight Color Operator Guide 4-23Problem SolvingInterposer problemsNOTE: Production publisher configuration onlyTable 4-2. Res
1-4 DocuTech 128/155/180 HighLight Color Operator GuideSafety noticesWARNING: This system is certified manufactured and tested in compliance with str
4-24 DocuTech 128/155/180 HighLight Color Operator GuideProblem SolvingFinisher problemsNOTE: Production publisher configuration onlyTable 4-3. Resol
DocuTech 128/155/180 HighLight Color Operator Guide 4-25Problem SolvingBinder tape faultNOTE: Production publisher configuration onlyTo clear a binde
4-26 DocuTech 128/155/180 HighLight Color Operator GuideProblem Solving2. Open the top cover.WARNING: The binder tape adhesive is hot, approximately
DocuTech 128/155/180 HighLight Color Operator Guide 4-27Problem SolvingNOTE: If the spool is empty, replace the stitcher spool A. Refer to online he
4-28 DocuTech 128/155/180 HighLight Color Operator GuideProblem Solving• The stitcher wire plug is located above the binder area, as shown in figure 4
DocuTech 128/155/180 HighLight Color Operator Guide 4-29Problem SolvingFigure 4-26 The measuring bracket8. Feed the wire until the wire touches the ba
4-30 DocuTech 128/155/180 HighLight Color Operator GuideProblem SolvingFigure 4-27 Removing the wire fragments10. Push the green stitcher head release
DocuTech 128/155/180 HighLight Color Operator Guide 4-31Problem Solving2. Hold the printed sheets by the top center of the short edge, keeping the ima
4-32 DocuTech 128/155/180 HighLight Color Operator GuideProblem Solvingdrive control panel if there is a tape drive problemYour call is answered by a
DocuTech 128/155/180 HighLight Color Operator Guide 5-15 Technical informationThis section contains the hardware and software capacity guidelines for
DocuTech 128/155/180 HighLight Color Operator Guide 1-5Safety noticesIn the event of problems, you should contact your local Xerox representative in t
5-2 DocuTech 128/155/180 HighLight Color Operator GuideTechnical informationPaper tray capacitiesStock weight(all trays)Substance 16 to 110 (60 to 200
DocuTech 128/155/180 HighLight Color Operator Guide 5-3Technical informationTray 4Stock SizesUS Letter (8 1/2 x 11 inches)US Legal (8 1/2 x 14 inches)
5-4 DocuTech 128/155/180 HighLight Color Operator GuideTechnical information223 x 297 mmISO B4JIS B4Custom (Width = 8 to 17 inches (203 to 432 mm), Le
DocuTech 128/155/180 HighLight Color Operator Guide 5-5Technical informationPrinter satisfaction guidesUse the following information to ensure your sa
5-6 DocuTech 128/155/180 HighLight Color Operator GuideTechnical informationStock satisfaction guidesTable 5-1. Satisfaction guide for paper trays 1 a
DocuTech 128/155/180 HighLight Color Operator Guide 5-7Technical informationTable 5-3. Satisfaction guide for paper trays 3, 4, 5, and 6NOTE: High vo
5-8 DocuTech 128/155/180 HighLight Color Operator GuideTechnical informationTable 5-4. Satisfaction guide for 2-sided printingUsing various stocksThe
DocuTech 128/155/180 HighLight Color Operator Guide 5-9Technical informationTable 5-5. Satisfaction guide for various stocksStock Type Instructions fo
5-10 DocuTech 128/155/180 HighLight Color Operator GuideTechnical information3 hole drilled, edge reinforced, 4024 DP paperDo not stitch or bind. Do n
DocuTech 128/155/180 HighLight Color Operator Guide 5-11Technical informationDo not use the following stocks:• Multipart forms• Stocks outside of the
1-6 DocuTech 128/155/180 HighLight Color Operator GuideSafety noticesCheck your understandingPlease review the questions and answers that follow to en
5-12 DocuTech 128/155/180 HighLight Color Operator GuideTechnical informationTable 5-7. Stock length impact on system performancePaper stock rotationT
DocuTech 128/155/180 HighLight Color Operator Guide 5-13Technical informationdevice that is not a Signature Booklet Maker, there is no message display
5-14 DocuTech 128/155/180 HighLight Color Operator GuideTechnical information*Although the diagonal meets the 18-inch (457 mm) rotation limit, the pap
DocuTech 128/155/180 HighLight Color Operator Guide 5-15Technical informationTable 5-10. Other paper sizes that can be rotatedFor media sizes that are
5-16 DocuTech 128/155/180 HighLight Color Operator GuideTechnical informationFinisher satisfaction guidesNOTE: Production publisher configuration onl
DocuTech 128/155/180 HighLight Color Operator Guide 5-17Technical informationTable 5-12. Stitcher satisfaction guideStock Reliable stacking may be exp
5-18 DocuTech 128/155/180 HighLight Color Operator GuideTechnical informationSet size limits Maximum collated:125 sheets of substance 20 (75 g/m2) or
DocuTech 128/155/180 HighLight Color Operator Guide 5-19Technical informationType or conditionXerographic bond paper in good conditionDrilled paperThe
5-20 DocuTech 128/155/180 HighLight Color Operator GuideTechnical information
DocuTech 128/155/180 HighLight Color Operator Guide 6-16 Service and suppliesAfter the installation of your printer, there are a few ongoing tasks tha
DocuTech 128/155/180 HighLight Color Operator Guide 1-7Safety noticesMUST BE CARRIED OUT ONLY BY PERSONS WHO POSSESS THE RELEVANT SKILL, KNOWLEDGE AND
6-2 DocuTech 128/155/180 HighLight Color Operator GuideService and suppliesThe key to effective use of the support center is correct identification of
DocuTech 128/155/180 HighLight Color Operator Guide 6-3Service and suppliesYour sales representative can help you submit the initial order of supplies
6-4 DocuTech 128/155/180 HighLight Color Operator GuideService and suppliesRoutine maintenanceThere are a number of routine maintenance tasks that mus
DocuTech 128/155/180 HighLight Color Operator Guide 6-5Service and suppliesTable 6-1. Consumable suppliesItem Description U.S. part number Paper Xero
6-6 DocuTech 128/155/180 HighLight Color Operator GuideService and supplies8.5 x 14 inch Dual Purpose Colors, Goldenrod 3R3094 8.5 x 11 inch Dual Pu
DocuTech 128/155/180 HighLight Color Operator Guide 6-7Service and supplies8.5 x 11 inch Custom form (uncut) Contact Xerox Supplies Order ServiceDry
6-8 DocuTech 128/155/180 HighLight Color Operator GuideService and suppliesBlue Developer Packaged 2 bottles per carton. Effective life is approximate
DocuTech 128/155/180 HighLight Color Operator Guide 6-9Service and suppliesCAUTION: *Do not use DT/DP Fuser Agent 8R2955 in a DT HLC printer. Do not
6-10 DocuTech 128/155/180 HighLight Color Operator GuideService and suppliesFuser shield LabelsTransparenciesCleaning suppliesOther Item Description Q
DocuTech 128/155/180 HighLight Color Operator Guide 6-11Service and suppliesIf you use custom colors, use the following table to help record the suppl
1-8 DocuTech 128/155/180 HighLight Color Operator GuideSafety noticesPerchlorate Law Compliance AnnouncementThis announcement is required for all Xero
6-12 DocuTech 128/155/180 HighLight Color Operator GuideService and supplies
DocuTech 128/155/180 HighLight Color Operator Guide 2-12 System componentsThe Xerox DocuTech HLC printers are electronic reprographics systems. They a
Prepared by:Xerox CorporationGlobal Knowledge and Language Services800 Phillips Road Bldg. 845-17SWebster, New York 14580USA©2007 by Xerox Corporation
2-2 DocuTech 128/155/180 HighLight Color Operator GuideSystem componentsOptional Components• Inverter Feeder/Stacker and up to 3 Feeder/Stackers• 2-Tr
DocuTech 128/155/180 HighLight Color Operator Guide 2-3System componentsData formats supportedThe Xerox DocuTech 128/155/180 HLC can print the followi
2-4 DocuTech 128/155/180 HighLight Color Operator GuideSystem componentsStock specificationsThe success of any print run depends on proper selection,
DocuTech 128/155/180 HighLight Color Operator Guide 2-5System components• Predrilled paper: Has holes for use in binders or binder rings. Before loadi
2-6 DocuTech 128/155/180 HighLight Color Operator GuideSystem componentsSystem software and job flowThis section describes how the system software pro
DocuTech 128/155/180 HighLight Color Operator Guide 2-7System componentsOutput queueAfter decomposition, the job is stored in the output queue.Printer
2-8 DocuTech 128/155/180 HighLight Color Operator GuideSystem componentsHigh volume printerThe components, special features, and configurations of the
DocuTech 128/155/180 HighLight Color Operator Guide 2-9System componentsProcessor feeder/paper traysTwo processor feeder/paper trays (trays 1 and 2) a
2-10 DocuTech 128/155/180 HighLight Color Operator GuideSystem componentsPaper LevelindicatorsDisplay the approximate quantity of paper in the tray. E
DocuTech 128/155/180 HighLight Color Operator Guide 2-11System componentsInverter feeder/stackerNOTE: High volume printer configuration onlyEach outp
DocuTech 128/155/180 HighLight Color Operator Guide iProduct Recycling and DisposalIf you are managing the disposal of your Xerox product, please note
2-12 DocuTech 128/155/180 HighLight Color Operator GuideSystem components Figure 2-5. High capacity stacker bin control panel1. Ready to Unload indica
DocuTech 128/155/180 HighLight Color Operator Guide 2-13System componentsHigh-capacitystackersThe high-capacity stacker (HCS) bins are located in the
2-14 DocuTech 128/155/180 HighLight Color Operator GuideSystem componentsProduction publisherThe standard base components, special features, and confi
DocuTech 128/155/180 HighLight Color Operator Guide 2-15System componentsInterposerNOTE: Production publisher configuration only.The 2-Tray or 3-Tray
2-16 DocuTech 128/155/180 HighLight Color Operator GuideSystem components3-Tray Interposer(productionpublisher only)The 3-Tray Interposer allows appli
DocuTech 128/155/180 HighLight Color Operator Guide 2-17System componentsFinisherNOTE: Production publisher configuration only Figure 2-11. FinisherI
2-18 DocuTech 128/155/180 HighLight Color Operator GuideSystem componentsThe stackerNOTE: Production publisher configuration onlyThe stacker collects
DocuTech 128/155/180 HighLight Color Operator Guide 2-19System componentsyou the information you need to create a personality profile for your third-p
2-20 DocuTech 128/155/180 HighLight Color Operator GuideSystem componentsHigh volume printer paper path The following figure shows the path the paper
DocuTech 128/155/180 HighLight Color Operator Guide 2-21System components4. High-capacity feeder tray 4a. Side 1 of sheet leaving feeder trayb. Drille
ii DocuTech 128/155/180 HighLight Color Operator Guide
2-22 DocuTech 128/155/180 HighLight Color Operator GuideSystem componentsProduction publisher paper pathThe following figure shows the path the paper
DocuTech 128/155/180 HighLight Color Operator Guide 2-23System componentsHigh volume printer bypass transport paper path Figure 2-14. Bypass transpor
2-24 DocuTech 128/155/180 HighLight Color Operator GuideSystem componentsThe SystemSystem HardwareThe basic hardware components of the DocuTech 128/15
DocuTech 128/155/180 HighLight Color Operator Guide 2-25System componentsAccessing FreeFlow Remote Print Server remotely FreeFlow Remote Print Server,
2-26 DocuTech 128/155/180 HighLight Color Operator GuideSystem componentsThe FreeFlow Print Server Tape Client software enables transmission of data f
DocuTech 128/155/180 HighLight Color Operator Guide 2-27System components Figure 2-16. Peripheral cabinet1. 9-track magnetic tape drive2. 18/36-track
2-28 DocuTech 128/155/180 HighLight Color Operator GuideSystem componentsLong and short edgefeedingTo feed through the printer, the leading edge of th
DocuTech 128/155/180 HighLight Color Operator Guide 3-13 Routine maintenanceThis section describes the routine activities you perform to maintain the
3-2 DocuTech 128/155/180 HighLight Color Operator GuideRoutine maintenancesupplies, you may damage the system.• Keep supplies in stock as listed in th
DocuTech 128/155/180 HighLight Color Operator Guide 3-3Routine maintenancePaperYou can add the same kind of paper to a tray when the supply is low wit
DocuTech 128/155/180 HighLight Color Operator Guideiii1 Safety noticesSystem safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-4 DocuTech 128/155/180 HighLight Color Operator GuideRoutine maintenanceFigure 3-2 Recommended temperature and humidity for paper storageConditioni
DocuTech 128/155/180 HighLight Color Operator Guide 3-5Routine maintenanceTable 3-1. Paper conditioningExample: If you want to move ten cartons of pap
3-6 DocuTech 128/155/180 HighLight Color Operator GuideRoutine maintenanceAdding paper to tray 1 or 2The following steps must be performed to add pape
DocuTech 128/155/180 HighLight Color Operator Guide 3-7Routine maintenanceFor stock outside the recommended limits, refer to the "Technical infor
3-8 DocuTech 128/155/180 HighLight Color Operator GuideRoutine maintenanceAdding paper to trays 3, 4, 5, or 6Paper Tray 3 is used to supply the larges
DocuTech 128/155/180 HighLight Color Operator Guide 3-9Routine maintenanceTable 3-2. Tray length settings for custom transfer assist blades (U.S. mark
3-10 DocuTech 128/155/180 HighLight Color Operator GuideRoutine maintenanceFigure 3-5 Measuring the paper cusers-guide-15392. Place the bottom edge of the prints
DocuTech 128/155/180 HighLight Color Operator Guide 3-11Routine maintenanceFigure 3-6 Measuring the paper curlNote: Corners of the sheets of paper sh
3-12 DocuTech 128/155/180 HighLight Color Operator GuideRoutine maintenanceAdjusting the decurler leverPerform the following steps to adjust the decur
DocuTech 128/155/180 HighLight Color Operator Guide 3-13Routine maintenanceMaintaining the printerA screen message is displayed when it is necessary t
iv DocuTech 128/155/180 HighLight Color Operator GuideReplacing the black dry ink bottle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-14 DocuTech 128/155/180 HighLight Color Operator GuideRoutine maintenanceFigure 3-8 Removing the empty bottle4. To insert a new bottle, place the b
DocuTech 128/155/180 HighLight Color Operator Guide 3-15Routine maintenanced. Hold the bottle in place with one hand and remove the paper seal by pull
3-16 DocuTech 128/155/180 HighLight Color Operator GuideRoutine maintenance3. Remove the empty container by grasping its handle. With a slow, firm mot
DocuTech 128/155/180 HighLight Color Operator Guide 3-17Routine maintenanceChanging the highlight color Customer Changeable UnitsThe highlight color C
3-18 DocuTech 128/155/180 HighLight Color Operator GuideRoutine maintenancec. When the HLC unit is level, tighten the lock nut. Figure 3-12 Leveling
DocuTech 128/155/180 HighLight Color Operator Guide 3-19Routine maintenance5. Then, turn the yellow CCU handle a quarter turn clockwise.Figure 3-13 U
3-20 DocuTech 128/155/180 HighLight Color Operator GuideRoutine maintenancethe cart. If the pallet does not move, check that the CCU is all the way ou
DocuTech 128/155/180 HighLight Color Operator Guide 3-21Routine maintenance3. Push the cart firmly against the printer until you can feel the two latc
3-22 DocuTech 128/155/180 HighLight Color Operator GuideRoutine maintenanceStoring the cart and CCUNOTE: If any dry ink gets on your hands, wash the
DocuTech 128/155/180 HighLight Color Operator Guide 3-23Routine maintenance5. Slide the stand toward the machine to engage the pins with the holes and
DocuTech 128/155/180 HighLight Color Operator Guide v5 Technical informationDocuTech printer specifications . . . . . . . . . . . . . . . . . . . .
3-24 DocuTech 128/155/180 HighLight Color Operator GuideRoutine maintenance6. Then, turn the yellow CCU handle a quarter turn clockwise.Figure 3-20 R
DocuTech 128/155/180 HighLight Color Operator Guide 3-25Routine maintenanceCAUTION: Fuser lubricant for other printers is not compatible.Do not use D
3-26 DocuTech 128/155/180 HighLight Color Operator GuideRoutine maintenanceFigure 3-22 Preparing to add fuser blendWARNING: Fuser lubricant spills c
DocuTech 128/155/180 HighLight Color Operator Guide 3-27Routine maintenanceFigure 3-23 Adding the fuser blende. Replace the reservoir cap by turning
3-28 DocuTech 128/155/180 HighLight Color Operator GuideRoutine maintenance7. Close the processor doors.The fuser blend message disappears after the s
DocuTech 128/155/180 HighLight Color Operator Guide 3-29Routine maintenance4. Insert the new waste HLC developer waste container into the transport as
3-30 DocuTech 128/155/180 HighLight Color Operator GuideRoutine maintenanceFigure 3-27 Flat cap on waste bottle4. Place the flat cap on the round bot
DocuTech 128/155/180 HighLight Color Operator Guide 3-31Routine maintenanceWire Module Removal and ReplacementReplace the wire module only when direct
3-32 DocuTech 128/155/180 HighLight Color Operator GuideRoutine maintenance2. Ensure that the brush on the wire module is at the toner bottle end as s
DocuTech 128/155/180 HighLight Color Operator Guide 3-33Routine maintenanceCleaning the system and its componentsNOTE: Follow the procedures in this
vi DocuTech 128/155/180 HighLight Color Operator Guide
3-34 DocuTech 128/155/180 HighLight Color Operator GuideRoutine maintenanceCleaning the 26-track cartridge tape driveThe 26-track, or quarter inch car
DocuTech 128/155/180 HighLight Color Operator Guide 3-35Routine maintenanceCleaning the sensors and the reflecting surfacesCAUTION: Never use abrasiv
3-36 DocuTech 128/155/180 HighLight Color Operator GuideRoutine maintenanceFigure 3-31 Area 4 and green handle3. Locate the Q850 and Q861 sensor.Figu
DocuTech 128/155/180 HighLight Color Operator Guide 3-37Routine maintenance4. Place a dry cleaning pad on the sensor and move it from left to right to
3-38 DocuTech 128/155/180 HighLight Color Operator GuideRoutine maintenanceFigure 3-34 Q1106 and Q1166 sensorsCleaning the Q1107 sensorNOTE: High vo
DocuTech 128/155/180 HighLight Color Operator Guide 3-39Routine maintenanceFigure 3-35 Q1107 sensorCleaning the Q1164 sensorNOTE: High volume printe
3-40 DocuTech 128/155/180 HighLight Color Operator GuideRoutine maintenanceFigure 3-36 Q1164 sensorCleaning the displayThe display should be cleaned
DocuTech 128/155/180 HighLight Color Operator Guide 3-41Routine maintenanceClearing or cleaning the finisher sensorsNOTE: Production publisher confi
3-42 DocuTech 128/155/180 HighLight Color Operator GuideRoutine maintenanceFigure 3-38 Locating the Q1201 sensor3. Brush a folded sheet of paper unde
DocuTech 128/155/180 HighLight Color Operator Guide 3-43Routine maintenanceFigure 3-39 Locating the Q1202 and Q1203 sensors3. Brush a folded sheet of
DocuTech 128/155/180 HighLight Color Operator Guide viiIntroductionAbout this guideThe guide is intended for Xerox DocuTech 128/155/180 HLC operators
3-44 DocuTech 128/155/180 HighLight Color Operator GuideRoutine maintenanceCleaning the Q1222 and Q1210 sensorsNOTE: Production publisher configurat
DocuTech 128/155/180 HighLight Color Operator Guide 3-45Routine maintenanceFigure 3-42 Locating the Q1222 and Q1210 sensors4. Wipe each sensor gently
3-46 DocuTech 128/155/180 HighLight Color Operator GuideRoutine maintenanceFigure 3-43 Locating the Q1205, Q1206, and Q1207 sensors4. Brush a folded
DocuTech 128/155/180 HighLight Color Operator Guide 3-47Routine maintenanceFigure 3-44 Q1213 sensor4. Brush a folded sheet of paper across the sensor
3-48 DocuTech 128/155/180 HighLight Color Operator GuideRoutine maintenanceFigure 3-45 Locating the Q1221, Q1218, and Q1227 sensorsCleaning the binde
DocuTech 128/155/180 HighLight Color Operator Guide 3-49Routine maintenance2. Grasp the green handle on the binder drawer. Pull the drawer out until i
3-50 DocuTech 128/155/180 HighLight Color Operator GuideRoutine maintenanceend tab. Move the cleaner back and forth until the end tab breaks.d. Contin
DocuTech 128/155/180 HighLight Color Operator Guide 3-51Routine maintenance1. Use the binder platen cleaner to clean the top and side surfaces of the
3-52 DocuTech 128/155/180 HighLight Color Operator GuideRoutine maintenanceFigure 3-50 Cleaning the flappersCleaning the calipersNOTE: Production p
DocuTech 128/155/180 HighLight Color Operator Guide 3-53Routine maintenanceFigure 3-51 Cleaning the calipersClosing the binderNOTE: Production publ
Comentários a estes Manuais